Last x Days Posts  1 | 3 | 7 Days  Search  Topics  Tree View  Help
  Soarer Central * Mechanical - TT * General Mechanical * Head gasket for 1JZ - 86.5mm Bore Previous Previous    Next Next  

Author Message
Fabian Bordon
TryHard
VIC
TT

Posts: 148
Reg: 02-2007

Top of pagePrevious messageNext messageBottom of page Link to this message

Rating: N/A
Votes: 0 (Vote!)

 Thursday, April 08, 2010 - 04:22 pm, by:  Fabian Bordon (Aether) Quote hilighted text Edit Post Delete Post Print Post   View Post/Check IP (Moderator/Admin Only) Move Post (Moderator/Admin Only)
What head gasket should I be using for a bore size of 86.5mm...I have had people say I can use the stock 86.0mm head gasket, and others saying to use an 87mm gasket...can anyone confirm and give a definitive answer :-)

Thanks.
Cihan Aday
Moderator
etuner.com.au
JZZ30

Posts: 3222
Reg: 07-2005

Top of pagePrevious messageNext messageBottom of page Link to this message

Rating: N/A
Votes: 0 (Vote!)

 Thursday, April 08, 2010 - 07:14 pm, by:  Cihan Aday (Cihan) Quote hilighted text Edit Post Delete Post Print Post   View Post/Check IP (Moderator/Admin Only) Move Post (Moderator/Admin Only)
Standard MLS gasket is 88mm, no problem with 1mm over or in your case, 0.5mm overbore.

;)
Fabian Bordon
TryHard
VIC
TT

Posts: 149
Reg: 02-2007

Top of pagePrevious messageNext messageBottom of page Link to this message

Rating: N/A
Votes: 0 (Vote!)

 Thursday, April 08, 2010 - 10:24 pm, by:  Fabian Bordon (Aether) Quote hilighted text Edit Post Delete Post Print Post   View Post/Check IP (Moderator/Admin Only) Move Post (Moderator/Admin Only)
Thanks Cihan, once again your feedback is appreciated :-)
Fabian Bordon
TryHard
VIC
TT

Posts: 150
Reg: 02-2007

Top of pagePrevious messageNext messageBottom of page Link to this message

Rating: N/A
Votes: 0 (Vote!)

 Thursday, April 08, 2010 - 10:54 pm, by:  Fabian Bordon (Aether) Quote hilighted text Edit Post Delete Post Print Post   View Post/Check IP (Moderator/Admin Only) Move Post (Moderator/Admin Only)
By any chance do you know what the HG thickness is after the head has been torqued down. I measured the head gasket out of the box and it measures 1.8mm. Just wanting to determine what the crush/squish on the HG would be?
Cihan Aday
Moderator
etuner.com.au
JZZ30

Posts: 3224
Reg: 07-2005

Top of pagePrevious messageNext messageBottom of page Link to this message

Rating: N/A
Votes: 0 (Vote!)

 Friday, April 09, 2010 - 07:00 am, by:  Cihan Aday (Cihan) Quote hilighted text Edit Post Delete Post Print Post   View Post/Check IP (Moderator/Admin Only) Move Post (Moderator/Admin Only)
Haven't measured but i'd assume 0.5mm crush to make it a 1.3mm gasket.

1/2JZ stuff is easy - just check clearances.

Add Your Message Here
Eye Candy
Click for full size
Bold text Italics Underline Center Text Upload photo from your hard drive Make a List Make a Table Make an Image Thumbnail Create a hyperlink Insert a clipart image Formatting Help
         

Username: Important Posting Information:
If asking a question, have you done a search to see if your question has already been answered?
Be aware that the use of SMS-speak eg "u" instead of "you" etc, will get your post deleted.
Password:
Enable HTML code in message
Automatically activate URLs in message

  Administration Administration      Log Out Log Out Previous Previous      Next Next